INSTALLATION Ferrari Portofino


STHFFI1

Comfort Roof Control Module for

  • Ferrari F8 Spider
  • Ferrari Portofino
  • Ferrari 296 GTS

    v1.0


    • Further information and manuals for all products can be found on our web site

    w w w . m o d s 4 c a r s . c o m

     
    We explicitly point out that all functions of this control unit should be used only while exercising caution and responsibility. We can NOT be held liable for any damage or injury caused by installing or using this product.
    PLEASE READ THE COMPLETE MANUAL CAREFULLY BEFORE USING THIS PRODUCT.
    Important Information. READ BEFORE INSTALLING!
    PRINTING THIS MANUAL
    This manual is designed to produce completely filled pages. In order to get best print results, simply set the borders to minimum settings in the browser's page setup menu and disable headers and footers.

    Activate the print preview and if necessary decrease the zoom level until all pages are shown correctly.

    ALL IMAGES CAN BE CLICKED FOR FULL SIZE in the browser.
    TROUBLE SHOOTING - NEED TO CONTACT US?
    If you run into any problems after installing the module, please go over the manual again in great detail, clicking every photo for full size!
    We now have a full Knowledge Base with Support Ticket system available online at www.mods4cars.com/support

    If you need to contact us, the best and fastest way to do so is by opening a support ticket there

    This module comes with our USB Field Upgrade and Configuration Port! We recommend connecting it to a computer BEFORE YOU INSTALL and using our support app "m4cconnect" to do a quick firmware update check. M4cconnect as well as all other information regarding USB update and configuration can be found at www.mods4cars.com/usb. You can even configure and activate your favorite module functions and settings on screen before the module is installed in the car! It is a good idea to permanently install the USB cable with the module in the car, leaving the computer plug in an easily accessible spot for later use with a Wifi/3G/4G connected laptop.
    IMPORTANT TROUBLESHOOTING TIPS

    If the top does not work properly or at all after installing the module, these tips can be very helpful:

    • 1) Turn Function 1 (Main Switch) off (Setting 0). The module will be completely passive. If the problem still persists and the top won't work, check all connections. Please also check the green DATA LED on the module!

    • 2) Function 2 now has a valet mode (Setting 2) on many modules. Valet mode completely disables opening of the top. Check the setting for function 2 and make sure the module is NOT in valet mode!

    IMPORTANT: Not all modules have the valet mode! Please check the Operation and Programming Manual!
    Installation - Steps 1-3
    1. Fully close the roof, turn the ignition off. Open the trunk and lift up the luggage divider.
    2. Removal of side panel: There are four T25 screws at the end nearer the rear of the car. The bottom screw is slightly longer than the other three and must go back in the same hole. There are three pegs/push pins at the end nearer the front of the car.
    3. Back area shown with screw and peg removed.
    Installation - Steps 4-6
    4. Pull the entire cover out. Behind it in the back corner is the black roof controller box.
    5. Removal of black roof controller box: There is a T25 screw at each end. Access to the one nearer the front of the car is blocked by a seat belt reel and bracket. If you have a tool combo, you can reach it. This screw goes through a slot rather than a hole, so it only needs to be loosened enough to allow the roof controller box to be pulled out to the rear of the car.
    6. Unplug the two marked plugs and replace them with the ones from the module harness, then connect the plugs to the sockets on the harness, connect the module itself. Tap the UNLOCK button on the remote once. The green LED on the module should flash to indicate proper installation. We recommend installing the USB cable and leaving it accessible for future updates and configuration. Don't forget to set the module functions up according to our operation and programming manual.